MR2 SpyderChat banner

21 - 29 of 29 Posts
G

·
Guest
Joined
·
0 Posts
Discussion Starter #21
Originally posted by bdee1
anybody knwo how to do thsi for a 2003 corolla S without the alarm (just keyless entry) i tried using the same procedure as the spyder and it does not work.
Did you try the other book I have posted? That works on my Avalon
 
G

·
Guest
Joined
·
0 Posts
Discussion Starter #23
My alarm wont stop goin off

I did everything right and both doors did unlock however my alarm wont deactivate. If anyone has any problem solvers please email me.
 

·
Registered
Joined
·
4,163 Posts
You, are correct, sir. Off it goes at 10:00 PM EDT. Last chance, trolls.
 

·
Registered
Joined
·
659 Posts
Here's the manual for changing the door unlocking behavior! It should presumably work on all new Toyotas with the keyless entry/immbolizer system (VIP RS3200).

Follow this procedure to change the operating functions of remote controls already programmed into a system. you may change the remote control's default unlock operation mode so that pressing the UNLOCK button once causes all doors to unlock at the same time. Also, you may activate the AUX button function on 4 button remote controls.
1. Before you begin: Open the driver's door and remove the key from the ignition switch.
2. Start the programming procedure. (Complete these steps within 40 seconds.)
a. Insert the key into and remove it from the ignition switch 2 times.
b. Close, then open the driver's door 2 times.
c. Insert the key into, and remove it from the igition switch 1 time.
d. Close, then open the driver's door 2 times.
e. Insert the key into, the ignition switch and leave it.
f. Close the driver's door.
g. Turn the key from LOCK to ON 4 times (ending at LOCK)
h. Remove the key from the ignition switch.
i. The tail and marker lights flash 4 times, the buzzer chirps 4 times and the doors lock and unlock 4 times.
* If the system does not activate the lights, buzzer and door locks 4 times, start over.
3. Select the operating functions for an existing remote control.
a. Press and release both the LOCK and UNLOCK buttons on one remote control at the same time.
b. Select one of the following modes:
I. Press and release the LOCK button to select the double unlock function (press the UNLOCK) button twice to unlock all the doors.
II. Press and release the UNLOCK button to select all door unlock function (press the UNLOCK button once to unlock all the doors at the same time.
III. Press and release the AUX button to select double unlock function (press the UNLOCK button twice to unlock all the doors) and activate the auxiliary output for the optional electric trunk release accessory.
IV. Press and release the PANIC button to select all door unlock function (press the UNLOCK button once to unlock all the doors at the same time) and activate the auxiliary output for the optional electric trunk release accessory.
* Program for 4 button remote controls only.
c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock and unlock 1 time.
Note: repeat the above steps to select the operating functions for additional remote controls.
* If the system activates the lights, buzzer and door locks 2 times, start over.
4. Complete the programming steps.
a. Open the driver's door.


Thanks to Green for posting this after the EZ-board link died.

G
 

·
Registered
Joined
·
1,652 Posts
remote ??

ok i have a ?? the guy that sold me the car has done several things i found odd wit my 00 spyder i only got one toyota key n when i asked him about it he gave me a spare u wud purchase at a hardware store, n also he never gave me the remote for the keyless entry idk if it comes with my car or not , im not really sure ne one know its a a yr 2000
 

·
Registered
Joined
·
10,809 Posts
Originally posted by Gibeon
I am looking for the instructions and can not remember if they're posted somewhere else or if it was on the SC two versions ago.

Please help.

Thank you.
Here's the manual for changing the door unlocking behavior! It should presumably work on all new Toyotas with the keyless entry/immbolizer system (VIP RS3200).

Follow this procedure to change the operating functions of remote controls already programmed into a system. you may change the remote control's default unlock operation mode so that pressing the UNLOCK button once causes all doors to unlock at the same time. Also, you may activate the AUX button function on 4 button remote controls.
1. Before you begin: Open the driver's door and remove the key from the ignition switch.
2. Start the programming procedure. (Complete these steps within 40 seconds.)
a. Insert the key into and remove it from the ignition switch 2 times.
b. Close, then open the driver's door 2 times.
c. Insert the key into, and remove it from the igition switch 1 time.
d. Close, then open the driver's door 2 times.
e. Insert the key into, the ignition switch and leave it.
f. Close the driver's door.
g. Turn the key from LOCK to ON 4 times (ending at LOCK)
h. Remove the key from the ignition switch.
i. The tail and marker lights flash 4 times, the buzzer chirps 4 times and the doors lock and unlock 4 times.
* If the system does not activate the lights, buzzer and door locks 4 times, start over.
3. Select the operating functions for an existing remote control.
a. Press and release both the LOCK and UNLOCK buttons on one remote control at the same time.
b. Select one of the following modes:
I. Press and release the LOCK button to select the double unlock function (press the UNLOCK) button twice to unlock all the doors.
II. Press and release the UNLOCK button to select all door unlock function (press the UNLOCK button once to unlock all the doors at the same time.
III. Press and release the AUX button to select double unlock function (press the UNLOCK button twice to unlock all the doors) and activate the auxiliary output for the optional electric trunk release accessory.
IV. Press and release the PANIC button to select all door unlock function (press the UNLOCK button once to unlock all the doors at the same time) and activate the auxiliary output for the optional electric trunk release accessory.
* Program for 4 button remote controls only.
c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock and unlock 1 time.
Note: repeat the above steps to select the operating functions for additional remote controls.
* If the system activates the lights, buzzer and door locks 2 times, start over.
4. Complete the programming steps.
a. Open the driver's door.


Thanks to Green for posting this after the EZ-board link died.

Posted by Don
 
21 - 29 of 29 Posts
Top